| CAMBRIDGE INSITU PARTS LIST |
| Cambridge self-boring pressuremeter and associated equipment |
| for insertion using INDEPENDENT POWER PACK |
| EITHER: |
| Cambridge Mark VIIId Digital Self Boring Pressuremeter, with |
| 50 metre cable length, 4 MPa maximum pressure rating, three strain |
| sensing arms with Fahey-Jewell rollers, two sealed gauge pore pressure |
| cells below the strain arms, downhole amplifiers, multiplexers and |
| RS 232 interface and fitted with standard self-boring cutting head |
| with replaceable edge shoe and RW size cutter drive rod. Gas pressure |
| line has 4 wire armoured cable carrying serial RS 232 data and Strain |
| Control Unit signal lines and instrument is supplied with computer |
| interface and power supply Unit, all tools, accessories, calibration devices |
| and fixtures and with data
logging software for Windows based PCs |
| OR: |
| Cambridge Mark Xd Digital Self Boring Pressuremeter with Six strain |
| sensing arms each with Fahey-Jewell rollers, all strain arms carried at |
| the same level and the pore pressure cells mounted above, all other details |
| as for Mark VIIId pressuremeter |
| PLUS EITHER: |
| Strain Control Unit for carrying out SBPM tests at constant rate of |
| strain, 4 MPa maximum pressure |
| OR: |
| High Pressure Strain Control Unit, with separated valve |
| unit, 10 MPa maximum pressure |
| AND THE FOLLOWING: |
| Analysis program, for clays
and for sands, running on Windows based PCs |
| High Pressure Manual
Pressure Control Unit containing |
| high precision pressure regulator, all necessary control and adjustable |
| bleed valves to carry out high quality stress controlled tests, in |
| diecast box. Maximum working
pressure 200 bars/20MPa |
| Standard Test Gauge, 250 mm diameter, ± 0.25% accuracy, |
| for independent calibration of pressure cells, in wood case with |
| appropriate adaptors |
| CAMBRIDGE INSITU PARTS LIST |
| Cutter Drive Unit, for use in conjunction with Hydraulic Ground |
| Frame to insert the SBPM, aluminium housing |
| 10 metres RW Cutter Drive Rods in 1.0 metre lengths plus 10 metres |
| Two Inch Casing in 1.0 metre lengths all packed in wood box |
| Hydraulic Ground Frame, for operating independently of |
| a rotary rig, may be screwed to casing or fixed down |
| to ground with screw anchors |
| Hydraulic Power Pack, V-twin cylinder petrol engine, with hydraulic |
| reservoir, hydraulic controls, all gauges, connections and hoses, mounted |
| in welded tubular frame. |
| Water Pump, two stage moineau type progressive cavity, hydraulically |
| driven from above power pack, with water pressure gauge and water |
| controls, in lightweight tubular frame |
| Ball Foot Clamp for 2" casing |
| OR for work in dense sands, weak rock or fragmented or shelly materials: |
| Weak Rock SBPM Conversion Kit containing 5 special membranes, |
| 1 special chinese lantern, 2 membrane clamping rings, 2 shoe edges, |
| shoe edge carrier, shoe body, special membrane fitting sleeve, |
| larger steel calibration cylinder, cutter spacers and full face cutter |
| with RW thread |
| CAMBRIDGE INSITU PARTS LIST |
| Cambridge Self-boring Pressuremeter and associated equipment |
| for insertion using a ROTARY RIG |
| EITHER: |
| Cambridge Mark VIIId Digital Self Boring Pressuremeter, with |
| 100 metre cable length, 4 MPa maximum pressure rating, three strain |
| sensing arms with Fahey-Jewell rollers, two sealed gauge pore |
| pressure cells below the strain arms, downhole amplifiers, multiplexers |
| and RS 232 interface and fitted with standard self-boring cutting head |
| with replaceable edge shoe and RW size cutter drive rod. Gas pressure |
| line has 4 wire armoured cable carrying serial RS 232 data and Strain |
| Control Unit signal lines and instrument is supplied with computer |
| interface and power supply Unit, all tools, accessories, calibration |
| devices and fixtures and with data logging software for IBM compatible |
| computer, |
| OR: |
| Cambridge Mark Xd Digital Self Boring Pressuremeter with |
| six strain sensing arms each with Fahey-Jewell rollers, all strain arms |
| carried at the same level and the pore pressure cells mounted above, |
| all other details as for Mark VIIId pressuremeter |
| PLUS EITHER |
| Strain Control Unit for carrying out SBPM tests at constant |
| rate of strain, 4 MPa maximum pressure |
| OR: |
| High Pressure Strain Control Unit, with separated valve |
| unit, 10 MPa maximum pressure |
| AND the following: |
| Analysis program, for clays
and for sands, running on Windows based |
| computer |
| High Pressure Manual
Pressure Control Unit containing |
| high precision pressure regulator, all necessary control and |
| adjustable bleed valves to carry out high quality stress controlled |
| tests. Mounted in diecast
box. Maximum working pressure 200 bars/20MPa |
| Standard Test Gauge, 250 mm diameter, ± 0.25% accuracy, for independent |
| calibration of pressure cells, in wood case with appropriate adaptors |
| CAMBRIDGE INSITU PARTS LIST |
| Rotary Rig Adaptor, type HHW, enabling rotary rig to insert |
| Self Boring Pressuremeter, with cutter position adjustment, |
| two water outlets and NWY box thread for mating to standard |
| rotary rig |
| 10 metres RW Cutter Drive Rods in 1.0 metre lengths plus |
| 10 metres Two Inch Casing in 1.0 metre lengths all packed in wood box |
| Ball Foot Clamp for 2" casing |
| OR for work in dense sands, weak rock or fragmented or shelly materials: |
| Weak Rock SBPM Conversion Kit containing 5 special membranes, |
| 1 special chinese lantern, 2 membrane clamping rings, 2 shoe edges, |
| shoe edge carrier, shoe body, special membrane fitting sleeve, |
| larger steel calibration cylinder, cutter spacers and full face cutter |
| with RW thread |
| SELF BORING PRESSUREMETER |
| MAJOR CONSUMABLE PARTS AND SPARES |
| These items are common to both methods of insertion |
| Adiprene Membranes, standard (0.050" thickness) |
| Weak Rock SBPM Membrane, nitrile rubber |
| Chinese Lanterns, all sizes, with screws (Except Rock SBPM) |
| Arm Springs, gauged and wired, each |
| Strain Arm pivots and bearings for 3-arm (set 6 bearings, 3 pins) |
| Strain Arm pivots and bearings for 6-arm (set 12 bearings, 6 pins) |
| Fahey-type bearings and pins for 3-arm (3 bearings, 3 pins) |
| Fahey-type bearings and pins for 6-arm (6 bearings, 6 pins) |
| Cutting Shoe Edges,all types |
| Cutter, spade, RW thread |
| Cutter, Rock Roller, Tricone 2.875", RW thread |
| Cutter, Full Face, Tungsten Carbide teeth, RW thread |
| Bottom Bearing, Gunmetal, RW type |
| 100 metre spare pressure hose assembly, ¼” bore c/w 4 way Rochester cable |
| CAMBRIDGE INSITU PARTS LIST |
| SELF-BORING PRESSUREMETERS and associated equipment |
| Cambridge Mark VIIId Digital Self Boring Pressuremeter, |
| with 100 metre cable length, 4 MPa maximum pressure rating, |
| three strain sensing arms with Fahey-Jewell rollers, two sealed |
| gauge pore pressure cells below the strain arms, downhole |
| amplifiers, multiplexers and RS 232 interface and fitted with |
| standard self-boring cutting head with replaceable edge shoe and |
| RW size cutter drive rod. Gas pressure line has 4 wire armoured |
| cable carrying serial RS 232 data and Strain Control Unit signal |
| lines and instrument is supplied with computer interface and power |
| supply Unit, all tools, accessories, calibration devices and fixtures |
| and with data logging software for Windows based computers |
| Cambridge Mark Xd Digital Self Boring Pressuremeter with Six strain |
| sensing arms each with Fahey-Jewell rollers, all strain arms carried at the |
| same level. The pore pressure cells have been moved to lie above the strain |
| measuring sensors. All other details as for Mark VIIId pressuremeter |
| Strain Control Unit for carrying out SBPM tests at constant rate |
| of strain, 4 MPa maximum pressure |
| High Pressure Strain Control Unit, with separated valve |
| unit, 10 MPa maximum pressure |
| Analysis program, for clays
and for sands, running on Windows based |
| computer |
| High Pressure Manual Pressure Control Unit containing |
| precision regulator and all necessary controls and adjustable bleed valves |
| to carry out stress controlled tests, in diecast box |
| Standard Test Gauges, 250 mm diameter, ± 0.25% accuracy, for |
| independent calibration of pressure cells, in wood case with appropriate adaptors |
| CAMBRIDGE INSITU PARTS LIST |
| Rotary Rig Adaptor, type HHW, enabling rotary rig to insert |
| Self Boring Pressuremeter, with cutter position adjustment, |
| two water outlets and NWY box thread for mating to standard |
| rotary rig |
| Cutter Drive Unit, for use in conjunction with Hydraulic Ground Frame to |
| insert the SBPM, aluminium housing |
| Cutter Drive Rod, RW type, one metre with coupler |
| Two Inch Casing, more rigid than EX Casing, |
| per one metre length |
| 10 metres RW Cutter Drive Rods in 1.0 metre lengths plus 10 metres |
| Two Inch Casing in 1.0 metre lengths all packed in wood box |
| Weak Rock SBPM Conversion Kit containing 5 special membranes, |
| 1 special chinese lantern, 2 membrane clamping rings, 2 shoe edges, |
| shoe edge carrier, shoe body, special membrane fitting sleeve, larger steel |
| calibration cylinder, cutter spacers and full face cutter with RW thread |
| |
| Hydraulic Ground Frame, for operating independently of a rotary rig, |
| may be screwed to casing or fixed down to ground with screw anchors |
| Hydraulic Power Pack, Diesel or petrol engine, hydraulic controls, |
| all gauges, connections and hoses, mounted in welded tubular frame. |
| The price has to depend on the exact specification chosen but is approximately |
| Water Pump, two stage moineau type progressive cavity, hydraulically driven |
| from above power pack, with water pressure gauge and water controls, |
| in lightweight tubular frame |
| Fahey-Jewell Roller conversion to existing three strain arm |
| Self Boring Pressuremeter |
| Ball Foot Clamp for 2" casing |
| CAMBRIDGE INSITU PARTS LIST |
| SELF BORING PRESSUREMETER CONSUMABLE PARTS AND SPARES |
| Adiprene Membranes, standard (0.050" thickness) |
| Adiprene Membranes, thin, (0.025" thickness) |
| Weak Rock SBPM Membrane, nitrile rubber |
| Ordinary SBPM Bag Clamp Rings (per pair) |
| Weak Rock SBPM Membrane Clamp Rings, per pair |
| Alencoflex Couplers, two part, all sizes ¼ BSP thread |
| Cable Coupler, SBPM to Alencoflex |
| Chinese Lanterns, all sizes, with screws |
| upper brass mounting ring |
| lower brass mounting ring |
| puller ring with screws |
| screws for puller ring only (3) |
| filler ring |
| O rings 038 lower 039 upper (2) |
| Shim pack |
| Syringe and needles, for de-airing pore pressure cell |
| O Ring Pack for K0 or SBPM |
| Screw Pack for SBPM |
| Screw Pack for K0 instrument |
| Pressure Cells .... |
| Pore Pressure Cell without cap |
| Pore Pressure Cell cap |
| Porous Inserts for PPC |
| Total Pressure Cell |
| CAMBRIDGE INSITU PARTS LIST |
| Resistor pack, 100 ohm - 1M ohm x 20% series, metal film |
| Arm Springs, gauged and wired, each |
| Strain Arm pivots and bearings for 3-arm (set 6 bearings,3 pins) |
| Strain Arm pivots and bearings for 6-arm (set 12 bearings, 6 pins) |
| Regauging otherwise good Total Pressure Cell |
| Regauging otherwise good Pore Pressure Cell |
| Strain Arm Calibrating fixture, for SBPM |
| Plastic tape for securing cable, per box of 36 rolls |
| Duct tape, Silver,per reel |
| SBPM Shoe Body |
| SBPM lock bolt |
| Weak Rock Self Boring Pressuremeter Shoe Body |
| Weak Rock Self Boring Shoe Edge Carrier |
| SBPM Shoe edge carrier, spade cutter type |
| Shoe Edge Carrier, 2.875” Rock Roller type |
| Cutting Shoe Edges, Rock Roller , Tricone 2.875", RW thread |
| Spade Cutter (3 sizes) |
| Weak Rock SBPM |
| Refurbished |
| Cutting Shoe, stainless steel, with non replaceable Edge |
| Cutter, Spade, RW thread |
| Cutter, Rock Roller, Tricone 2.875", RW thread |
| Cutter, Full Face, Tungsten Carbide teeth, RW thread |
| Bottom Bearing, Gunmetal, RW type |
| CAMBRIDGE INSITU PARTS LIST |
| Top Bearing Adaptor |
| Bearing for Top Bearing Adapter, per set of 2 |
| Bearing, ball thrust, for Rotary Rig Adapter |
| Cutter Drive Rod, RW type, 1 metre with coupler |
| Cutter Drive Rod, RW type, 1 metre no coupler |
| Cutter Drive Rod, RW type, coupler only |
| Cutter Drive Rod, RW type, for Rotary Rig Adapter (short length) |
| Cutter Drive Rod for Cutter Drive Unit, RW |
| Cutter Spacing Rings, RW type, steel, pack of assorted |
| Cutter Bearing Rings, RW type, Tufclad-Moly, each |
| EX to two inch Casing adaptor, long or short |
| Instrument Cutter Drive Rod, RW type |
| Two inch casing, left hand thread, metre lengths |
| Cutter Drive Unit: set of oil seals & O rings |
| collet |
| Collet locking nut |
| Victor Titley Water Swivel Packing, set |
| Victor Titley Water Swivel |
| Water Swivel Coupler |
| CAMBRIDGE INSITU PARTS LIST |
| Outlet hose, per metre |
| |
| Hydraulic Pressure Hose, 1/2" bore, 5 metres long, |
| complete with quick release couplers |
| Water Delivery pressure hose, as above |
| SBPM over membrane calibration cylinder |
| |
| SBPM over chinese lantern calibration cylinder |
| Pressure Control Panel valve sleeves, set of 5 |
| Engine Oil Filter, or Air Filter (Lister), each |
| Strain Control Unit parts |
| |
| Valve assembly, without pressure cell |
| Valve Orifice |
| Pressure Transducer, gauged and wired |
| Valve assembly with pressure transducer |
| Vacuum pump (complete) |
| Vacuum pump (bare) |
| Quick Release gas couplers, CEJN type, mated pair |
| Water pump stator, rubber |
| Water pump rotor, Stainless, hard chrome plated |
| Desiccator |
| “Pressuremeter Testing” by Mair &Wood, per copy |
| “Pressuremeters in Geotechnical Design” by B G Clarke, per copy |
| Casing adapters, 6”, 8” or 10” |
| CAMBRIDGE INSITU PARTS LIST |
| SBPM and other Cables .... |
| 100 metre, Rochester, 6mm hose only |
| 100 metre, Rochester, 6mm hose, both ends fitted & wired |
| Windlass |
| 6 metre gas pressure line with CEJN couplers |
| Gas/Electricity Separating Union, complete with |
| glass to metal seal, HPD design, unwired |
| CAMBRIDGE INSITU PARTS LIST |
| WEAK ROCK SELF BORING PRESSUREMETERS and associated equipment |
| Weak Rock SBPM Conversion Kit containing 5 special membranes, |
| 2 membrane clamping rings, 2 shoe edges, shoe edge carrier, shoe body, |
| special membrane fitting sleeve, larger steel calibration cylinder, cutter |
| spacers and full face cutter with RW thread and 1 Chinese Lantern |
| SELF BORING PRESSUREMETER CONSUMABLE PARTS AND SPARES |
| Weak Rock SBPM Membrane, nitrile rubber |
| Weak Rock SBPM Membrane Clamp Rings, per pair |
| Weak Rock Self Boring Pressuremeter Shoe Body |
| Weak Rock Shoe Edge Carrier |
| Cutting Shoe Edges, weak rock SBPM |
| Refurbished shoe edges |
| Cutter, Rock Roller, Tricone 2.875”, RW thread |
| Cutter, Full Face, Tungsten Carbide teeth, RW thread |
| Bottom Bearing, Gunmetal, RW type |
| Chinese Lantern, complete |
| Chinese Lantern strips per set of 6, c/w screws |
| Chinese Lantern rings per set |
| Chinese Lantern shims per set |
| CAMBRIDGE INSITU PARTS LIST |
| CONE PRESSUREMETERS and associated equipment |
| Cambridge Insitu Mark IId direct strain measuring Cone Pressuremeter to fit |
| behind all standard 15 sq cm cones. Expanding length 445 mm and complete |
| with membrane, chinese lantern protective sheath, cone spacer, amplifier sub, |
| cable connections, all tools for calibration cylinder all in wood box and complete |
| with 50 metres of detachable pressure hose containing electrical cable, carried |
| on reel and windlass, with gas/electricity separating union mounted on cable reel |
| and complete with connecting cable to Electronics Unit |
| Cone Electronics Unit for use with Mk II Cone Pressuremeter |
| including power supply for the pressuremeter, connector for cable to Cone |
| electronics, multiplexer, 4½ digit analogue to digital conversion, RS 232 serial |
| output port for computer and furnishing Total Strain signal for driving Strain |
| Control Unit |
| Strain Control Unit for carrying out Cone Pressuremeter tests at constant |
| rate of strain 4 MPa maximum pressure |
| Cone Pressuremeter Analysis program, for clays and for sands, running on |
| IBM compatible computer and with printer drivers for all common printers |
| Pressuremeter Pressure Control Panel, uses one 150 mm diameter 1% accuracy |
| gauge and all necessary control valves. The panel is fixed inside the same |
| wooden box used to carry the Strain Control Unit and Electronics Unit |
| Standard Test Gauges, 250 mm diameter, ± 0.25% accuracy, for independent |
| calibration of Total Pressure cell, in wood case with appropriate adapters and |
| calibration certificate |
| SPARES & CONSUMABLE PARTS |
| Spare Cone Pressuremeter centre section ready assembled for |
| immediate plug-in replacement for unit damaged whilst testing |
| Adiprene Membranes |
| Chinese Lantern |
| Electronics Can |
| Total Pressure Cell |
| Strain Arm Springs, gauged and wired, each |
| Strain Arm pivots and bearings for 3-arm (set 6 bearings, 3 pins) |
| Fahey-type pins and bearings for 3-arm (set 3 bearings, 3 pins) |
| Lantern securing rings (“finger rings”) |
| Cable, 50 metres, with identical end fittings |
| CAMBRIDGE INSITU PARTS LIST |
| High Pressure Dilatometers |
| The High Pressure Dilatometers are now supplied in two sizes. |
| The original size is 73 mm diameter for use in NX size Boreholes of 76.0 mm |
| nominal diameter. |
| The later version is 95 mm in diameter and is intended for use in H size |
| boreholes,approximately 98 mm in diameter. |
| HPD 73 mm diameter, Mark IV complete with downhole amplifiers, compass, |
| multiplexer and RS 232 interface, 75 metre oil line and armoured cable assembly |
| on windlass. Supplied with computer interfacing equipment and IBM compatible |
| data logging software, 20 MPa Pressure Rating |
| HPD 73 mm diameter to above specification but with 30 MPa Pressure Rating |
| Spare parts pack for the 73 mm instrument, |
| containing quantities as in [ ] below |
| Individual Spares: |
| Chinese Lantern complete with end rings [2] |
| Chinese Lantern Spacers, per pair |
| Chinese Lantern strips, with rivets, per set [5] |
| Nitrile Rubber Membrane (Reinforced) each (5mm thick) |
| Nitrile Rubber Membrane (8mm thick) each |
| Nitrile Rubber Membrane (5mm thick) each [5] |
| Extrusion Preventers (Christmas trees), per pair [10] |
| Chinese Lantern Rings, per pair, upper and lower |
| Stainless pop rivets for Chinese Lantern Rings, per set |
| Membrane Clamping Rings, each |
| Strain follower sensing spring for Analogue 73HPD, Beryllium copper, gauged, |
| wired and coated |
| Strain follower sensing spring for Mk IV, Beryllium copper, gauged, |
| wired and coated for Mark IV 73HPD |
| 100 metre replacement cable, 4 wire Rochester cable, 8mm hose, |
| both ends fitted & wired, includes OESU & HPD top adapter, ready to use |
| ¼” Quick Release Coupling (female) |
| ¼” Quick Release Coupling (male) |
| Over Chinese Lantern Calibration Cylinder, screwed in ends |
| CAMBRIDGE INSITU PARTS LIST |
| 95 mm diameter High Pressure Dilatometer, Mark I |
| 95HPD Mark I complete with downhole amplifiers, compass, multiplexer and |
| RS 232 interface, 75 metre oil line and armoured cable assembly on windlass. |
| Supplied with computer interfacing equipment and IBM compatible |
| logging software, 20 MPa Pressure Rating |
| 95 HPD diameter, to above specifications but with 30 MPa Pressure Rating |
| Spare parts pack for the 95 mm instrument, |
| containing quantities as in [ ] below |
| Individual Spares: |
| Chinese Lantern complete with end rings [2] |
| Set of Chinese Lantern strips, with rivets [5] |
| Nitrile Rubber Membrane (Reinforced) each |
| Nitrile Rubber Membrane (nominal 6mm thick) each [5] |
| Extrusion Preventers (Christmas trees), per pair [10] |
| Chinese Lantern Rings, per pair, upper and lower |
| Stainless pop rivets for Chinese Lantern Rings, per set |
| Sleeve Clamp Ring, each (aluminium bronze) |
| Strain follower sensing spring, Beryllium copper, gauged, wired and coated |
| Strain Sensing Arm Assembly |
| Strain Sensing Arm Spring Assembly - rebuilt |
| Strain Arm Followers, complete with bearings, each |
| Strain Arm pivots and bearings for 6-arm (set of 12 bearings, 6 pins) |
| Fahey-type bearings and pins for 6-arm (set 6 bearings, 6 pins) |
| Button bearings (set 6 bearings, 6 pins) |
| 100 metre replacement cable, 4 wire Rochester cable, 8mm hose, |
| both ends fitted & wired, includes OESU & HPD top adapter, ready to use |
| 150 metre hose/cable assembly as above specification |
| 200 metre hose/cable assembly as above specification |
| 300 metre hose/cable assembly as above specification (special) |
| 200 metre hose/cable assembly, 8mm hose, 7 wire Rochester fitted both ends |
| with special cable couplers |
| Special linking curly cable for use with above |
| Cable Coupler |
| CAMBRIDGE INSITU PARTS LIST |
| Equipment and spares common to both sizes of HPD |
| Hydraulic hand pump, with 0 - 200 Bar, 1% gauge |
| Analysis software for IBM compatible computer |
| Standard Test Gauge, 0 - 250 Bar f.s.d., 0.25%, with |
| adaptors and in protective wooden case |
| High Pressure Manual Pressure Control Panel for using the 73 or 95 HPD on |
| compressed nitrogen, fitted with one 250 mm diameter Standard Test Gauge |
| of ±0.5% accuracy, standard range 0 to 25 MPa f.s.d. Panel contains high |
| precision manual pressure regulator, all necessary control and adjustable |
| bleed valves, in wood case |
| ‘C’ Spanner |
| Split cover sleeve |
| Total Pressure cell |
| HPD cables and hose assemblies as spares |
| 100 metre with Rochester cable in 8mm hose only |
| 150 metre with Rochester cable in 8mm hose only |
| 200 metre with Rochester cable in 8mm hose only |
| HPD Oil Return hoses and Bleed tubes |
| 100 metre Oil Return line, 6mm hose, with ends |
| 250 metre Oil Return Line, 6mm hose, with ends |
| Bleed tube connector for probe, with union |
| Bleed tube connector, socket fitting, with union |
Last Updated on 25/04/2012 by Robert